ACV 43XFT03 i-dapterCitroen/Fiat/Opel/Peugeot/Toyota Multilead
EAN: 4026724679540
43XFT03
Infodapter
Citroen Jumper 2024 - 2026
Fiat Ducato: 2021 - 2026
Opel Movano: 2024 - 2026
Peogeot Boxer: 2024 - 2026
Toyota Proace Max: 2024 - 2026
Read More
1 pcs
189,90 €
Description
Specifications
i-dapter Citroen / Fiat / Opel / Peugeot / Toyota
The Infodapter will retain several vehicle display functions when the OEM radio or navigation system is replaced.
Vehicle specific settings are accessible and will be displayed on the aftermarket head unit.
SWC buttons are essential to get access to the Infodapter configuration menu.
Also check our listed OEM head units and compare the pictured harness connectors with the connectors in your car and make sure that they fit optically and technically.
Note that in some cases not all functions are supported.
For example Trailer Assist, E Call or other driver assistance and comfort systems.
Check the vehicle menu for various settings before installation.
Check the function of the settings and the vehicle system before final installation.
Please contact our support team for help.
02431-9645-96
[email protected]
Note:
vehicles with SWC
CAN BUS
connector: 12 Pin green / 32 Pin blue Fiat
connector: OEM SWC 3,5mm Jack / loose wire
vehicles with 5″ OEM HU
vehicles with 7″ OEM HU
vehicles with 10″ OEM Sat Nav
activate and configure the rear view camera input in the retrofit HU
connection i-dapter:
purple/white: +12V reverse gear signal
RCA(m) ochre: rear view camera input retrofit HU
visualisation i-adapter settings retrofit HU rear view camera input
camera image or i-dapter settings and visualisation not available:
connect additional GND signal to the RCA outer conductor of the camera and HU connection
i-dapter settings:
press and hold track up or down SWC buttom
depending on the vehicle equipment and software:
not all vehicle settings are supported
not all vehicle functions are supported
not all vehicle information is visualised
+12V reverse gear signal not reliably supported
following settings supported:
Language / Distance Units / Clock / Temperature Units / Consumption Units / Speed Units / Follow Me / Auto Door Unlock on Exit / Flash Lights with lock / Courtesy Lights / Auto Door Locks / Daytime Running Lights / Cornering Lights / Ambient Lighting / Greeting Lights / Park Sens / Volume Level / High Beam Control / Park Sense / Rain Sensor / Lane Sense Warning / Lane Sense Strength / Tyre Pressure Units / Traffic Sign Recognition / Traffic Sign Warning / Vehicle Off Options / Blindspot Assist / Headlight Sensor Sensitivity / Forward Collision Warning / Forward Collision Sensitivity
+12V reverse gear signal not reliably supported
vehicles with OEM rear view camera:
Rear view camera interface Citroen/Fiat/ Opel/OEM camera item: 771094-1031
DIP switch settings without the power connection
reconnect the interface once the settings have been made
dip switch settings for the OEM device (look into the manual)
dip switch settings for the retrofit device manufacturer (look into the manual)
The Infodapter will retain several vehicle display functions when the OEM radio or navigation system is replaced.
Vehicle specific settings are accessible and will be displayed on the aftermarket head unit.
SWC buttons are essential to get access to the Infodapter configuration menu.
Also check our listed OEM head units and compare the pictured harness connectors with the connectors in your car and make sure that they fit optically and technically.
Note that in some cases not all functions are supported.
For example Trailer Assist, E Call or other driver assistance and comfort systems.
Check the vehicle menu for various settings before installation.
Check the function of the settings and the vehicle system before final installation.
Please contact our support team for help.
02431-9645-96
[email protected]
Note:
vehicles with SWC
CAN BUS
connector: 12 Pin green / 32 Pin blue Fiat
connector: OEM SWC 3,5mm Jack / loose wire
vehicles with 5″ OEM HU
vehicles with 7″ OEM HU
vehicles with 10″ OEM Sat Nav
activate and configure the rear view camera input in the retrofit HU
connection i-dapter:
purple/white: +12V reverse gear signal
RCA(m) ochre: rear view camera input retrofit HU
visualisation i-adapter settings retrofit HU rear view camera input
camera image or i-dapter settings and visualisation not available:
connect additional GND signal to the RCA outer conductor of the camera and HU connection
i-dapter settings:
press and hold track up or down SWC buttom
depending on the vehicle equipment and software:
not all vehicle settings are supported
not all vehicle functions are supported
not all vehicle information is visualised
+12V reverse gear signal not reliably supported
following settings supported:
Language / Distance Units / Clock / Temperature Units / Consumption Units / Speed Units / Follow Me / Auto Door Unlock on Exit / Flash Lights with lock / Courtesy Lights / Auto Door Locks / Daytime Running Lights / Cornering Lights / Ambient Lighting / Greeting Lights / Park Sens / Volume Level / High Beam Control / Park Sense / Rain Sensor / Lane Sense Warning / Lane Sense Strength / Tyre Pressure Units / Traffic Sign Recognition / Traffic Sign Warning / Vehicle Off Options / Blindspot Assist / Headlight Sensor Sensitivity / Forward Collision Warning / Forward Collision Sensitivity
+12V reverse gear signal not reliably supported
vehicles with OEM rear view camera:
Rear view camera interface Citroen/Fiat/ Opel/OEM camera item: 771094-1031
DIP switch settings without the power connection
reconnect the interface once the settings have been made
dip switch settings for the OEM device (look into the manual)
dip switch settings for the retrofit device manufacturer (look into the manual)
Vehicle application:
Citroen
Citroen Jumper (250) 07/2024 -2026
Citroen e-Jumper (259 07/2024 -2026
Citroen Relay (250) 2024 - 2026
Fiat
Fiat Ducato (ZAF 250) 11/2021 - 11/2023
Fiat Ducato (ZAF 250) 11/2023 - 2026
Fiat e-Ducato (ZAF 250) 04/2021 - 03/2024
Fiat e-Ducato (ZAF 250) 03/2024 -2026
Opel
Opel Movano Cargo C (Y) 01/2024 - 2026
Opel Movano Electric Cargo C (Y) 01/2024 - 2026
Peugeot
Peugeot Boxer (Y) 07/2024 - 2026
Peugeot e-Boxer (Y) 07/2024 - 2026
Toyota
Toyota Proace Max (T) 08/2024 - 2026
Toyota Proace Max Electric (T) 01/2025 - 2026
Following signals are provided:
Reimported vehicles or vehicles with different software may be incompatible in functions.
red: +12V ignition clamp 15
orange: +12V illumination clamp 58
purple/white: +12V reverse gear signal not in all vehicles supported
pink: speed pulse signal not reliably supported
green: GND park brake signal
load capacity outputs: 250 mA max.
current requirement more than 250 mA:
1 relay coil resistance 75 Ohm min.
2 relays coil resistance 150 Ohm min.
SWC
vehicle settings supported
General installation instructions:
Verification:
1: Check all operating functions and vehicle setting functions of the OEM HU.
2: Disconnect the OEM HU voltage-free.
3: Check all interface connections for correctness voltage-free.
Connection and connection sequence:
1: Check settings and hardware configuration of the interface voltage-free.
2: Check configuration of the HU connection cable voltage-free.
3: Connect the HU connection cable according to the operating instructions of the retrofit HU.
4: Connect all other connections according to the operating instructions of the retrofit HU.
5: Connect the entire installation to the vehicle with the main connection last.
6: Software configuration of the interface according to the instructions in the item text and in the manual.
7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.
8: Function test of steering wheel remote control and vehicle
Changes to the configuration of the interface and the HU connection cable:
1: Change configuration voltage-free
2: Reconnection see above 5 to 8
In case of malfunction of the interface or the vehicle:
1: Reinstall the OEM HU
2: Operate the OEM HU
3: Establish CAN bus shut down
4: Check the hardware configuration of the interface
5: Reconnection after CAN Bus shut down see above 5 and 6
More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.
More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes are to be carried out exclusively by trained specialist installer.
2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle′s cable assignment diagram before connection.
4: Connections and modifications are made on the user′s own responsibility without guarantee of function.
5: Connections and modifications are made on the user′s own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.
6: Modifications to the pre-assembled wiring harness may invalidate the product′s warranty.
Citroen
Citroen Jumper (250) 07/2024 -2026
Citroen e-Jumper (259 07/2024 -2026
Citroen Relay (250) 2024 - 2026
Fiat
Fiat Ducato (ZAF 250) 11/2021 - 11/2023
Fiat Ducato (ZAF 250) 11/2023 - 2026
Fiat e-Ducato (ZAF 250) 04/2021 - 03/2024
Fiat e-Ducato (ZAF 250) 03/2024 -2026
Opel
Opel Movano Cargo C (Y) 01/2024 - 2026
Opel Movano Electric Cargo C (Y) 01/2024 - 2026
Peugeot
Peugeot Boxer (Y) 07/2024 - 2026
Peugeot e-Boxer (Y) 07/2024 - 2026
Toyota
Toyota Proace Max (T) 08/2024 - 2026
Toyota Proace Max Electric (T) 01/2025 - 2026
Following signals are provided:
Reimported vehicles or vehicles with different software may be incompatible in functions.
red: +12V ignition clamp 15
orange: +12V illumination clamp 58
purple/white: +12V reverse gear signal not in all vehicles supported
pink: speed pulse signal not reliably supported
green: GND park brake signal
load capacity outputs: 250 mA max.
current requirement more than 250 mA:
1 relay coil resistance 75 Ohm min.
2 relays coil resistance 150 Ohm min.
SWC
vehicle settings supported
General installation instructions:
Verification:
1: Check all operating functions and vehicle setting functions of the OEM HU.
2: Disconnect the OEM HU voltage-free.
3: Check all interface connections for correctness voltage-free.
Connection and connection sequence:
1: Check settings and hardware configuration of the interface voltage-free.
2: Check configuration of the HU connection cable voltage-free.
3: Connect the HU connection cable according to the operating instructions of the retrofit HU.
4: Connect all other connections according to the operating instructions of the retrofit HU.
5: Connect the entire installation to the vehicle with the main connection last.
6: Software configuration of the interface according to the instructions in the item text and in the manual.
7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.
8: Function test of steering wheel remote control and vehicle
Changes to the configuration of the interface and the HU connection cable:
1: Change configuration voltage-free
2: Reconnection see above 5 to 8
In case of malfunction of the interface or the vehicle:
1: Reinstall the OEM HU
2: Operate the OEM HU
3: Establish CAN bus shut down
4: Check the hardware configuration of the interface
5: Reconnection after CAN Bus shut down see above 5 and 6
More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.
More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes are to be carried out exclusively by trained specialist installer.
2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle′s cable assignment diagram before connection.
4: Connections and modifications are made on the user′s own responsibility without guarantee of function.
5: Connections and modifications are made on the user′s own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.
6: Modifications to the pre-assembled wiring harness may invalidate the product′s warranty.